Fairfax, VA

New HVAC Installation: removed all old refrigerant and removed all old equipment and set and installed all new equipment and tied everything back in from lineset to wiring and drains and duct work and gas also toed in outdoor unit and fired everythjng up and checked for proper operation and set and installed new water heater and tied everything back in and checked for proper operation of heater

Heat Turns On, Then Turns Off: daikin gas furnace turned on when I increased the heat. I cleaned flame sensor and checked micro amps reading 3.1. I decreased gas pressure. inducer reading .38 amps ok. blower 4.2 amps ok. return 70 supply 124. Co combustion stack temp 330, oxygen 7.4, co 50 ppm heat exchanger in good shape. ignitor ohms 56 ok. filter and return grill is dirty needs to be replaced and cleaned. system is heating properly at this time.

I inspected 80 percent gas furnace. I replaced 20x25x4 filter and dated. I replaced humidifier pad and set controls to 35%. flame sensor was dirty so I removed and cleaned, sensor is also reading 3 micro amps. I checked all safeties and switches. ignitor is reading 48 ohms. blower is pulling 4.03 amps and inducer pulling 1.04. return is 72 supply is 128. I also completed co combustion analysis on system. gas furnace is heating properly at this time. Thank you for choosing vito services.

Call to do maintenance on 2022 heat pump system. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. Found blower is clean along with evaporator coil. Checked air filter and water panel both are good. Checked condenser unit and found no issues as well. Final cycled system at this time system is operational.

performed maintenance on 2 systems. Checked 2015 heat pump in attic first. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. Blower is clean and in good condition. All elements are amping at 20. System didn't have air scrubber and humidifier. Heat pump components are good outside. Condenser coil needs to be clean ($247). Checked basement 2011 Furnace only system. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. Blower is clean air filters need to be changed. Performed combustion analyzer test system is in good standing. Final cycled system at this time system is operational. Basement system is best placement for Air scrubber and humidifier.

FALL MAINTENANCE ON ONE UNIT 2022 80% CARRIER GAS FURNACE I checked the filter and replaced with one costumer provided. I checked the ECM motor and noticed that as of right now it is exposed to any high voltage power surges due to not containing a surge protector. I checked the motor amps found okay. I checked the inducer draft motor and flue vent pipe and found okay I checked inducer amps. I checked and cleaned the burners and heat exchanger. I checked the flame sensor and cleaned it off I checked the Ignitor ohms reading 55ohms. I checked gas valve, I checked for any leaks and found none. I checked all limits and saftys and all wirings and connections found okay. I got a return air temp of 132 and a supply air temperature of 79. This unit is new and running efficiently with no issues at this time. I checked full operation and all checked out. Recommendations: Add Ecm surge protector $309.00 Continue with annual maintenance I will advise client of findings and recommendatio

Replaces both flame sensors and added both Ecm surge protectors. Will collect remaining balance. If there is any issues or concerns please feel free to reach out to Vito services. Thank you. The total is $1092.00 i collected $546 under check number #442 on 11/06/24 not $1092.00 Today I will collect the remaining balance of $546.00

NO AC R22 FROZEN SYSTEM I arrived today and called for AC , system automatically started freezing up. The system is running off of R-22 we no longer carry r-22. There must be a major leak somewhere in the system. Due to us no longer carrying r-22 we can no longer try to repair the unit. The system has a block of ice on it. Due to the age , and none reliability and parts being worn out I recommend clients upgrades the unit. The furnace is also passed its life expectancy and you do not want to put a new AC coil on top of a old furnace. Therefore I will recommend replacing full system. We will get proposal for client on full system and AC only as well. All pictures were uploaded and sent to Moe with measurements as well. He is working on a proposal for the client. Thank you for choosing VITO SERVICES.

New Furnance Installation: recovered all old refrigerant and removed all old equipment. set and installed all new equipment and tied all lines back in and wiring and drains and installed new thermostat and fired up all equipment and checked for proper operation

FALL MAINTENANCE ON TWO UNITS. #1 Attic. I checked full operation of unit in low heat and I'm high heat. Filter had been replaced upon today's arrival. I checked the ECM motor and as of right now it is exposed to any high voltage power surges. I checked amps and found okay I checked all wiring and connections found okay. I checked all limits and safetys. I noticed back draft on 80% furnace so I did a combustion test and found system safe to operate. I checked and cleaned burners and heat exchanger I checked inducer motor and amps i checked flue vent pipe okay. I checked Ignitor reading 55ohms I checked flame sensor and found dirty and no longer reliable. I got a return air temperature of 70 and a supply air temperature of 118. This unit is running and heating as of now. Recommendations for unit #1 Add ECM surge protection $199.00 Replace flame sensor $347.00 #2 Basement. I checked filter and replaced with one Costumer provided. I checked the ECM motor and this motor is also

Error Code on Thermostat and Red Light "No Water" on Humidifier: HUMIDIFIER HAS NO WATER. The Valve for the humidifier at the water heater is leaking. I tightened it with a adjustable wrench to stop the leaking for the mean time. we will have to return to replace the valve. Total price to replace valve. $642.00 The costumer will like to get another quote and will contact us back. Thank you for choosing VITO SERVICES

FALL MAINTENANCE ON ONE UNIT. I checked the filter and found okay as of now. I checked indoor blower wheel motor housing compartment for any obstructions and found none. I checked blower amps found within specs. I checked the inducer draft motor and flue vent pipe found okay. I checked inducer amps found okay. i checked and cleaned burners and heat exchanger found okay. I checked for any gas leaks found none. I checked all wiring and connections all limits and safety found okay. parts are reliable. The UV light is on a running. I got a return air temperature of 70 and a supply air temperature of 120 The humidifier is not in use it is just sitting there as of right now. I checked outdoor unit heat pump parts are okay. Surge protector is intact and working fine as of now. This unit is running and heating as of now with no issues. Recommendation: Annual vito vip maintenance contract $244.00 I will ask client if he would like to sign up. Thank you for choosing VITO SERVICES.

FALL MAINTENANCE #1) Basement/Main level The filter was replaced with one costumer provided. Indoor air handler is clean and efficient with parts being reliable. All wiring's and connections found okay. I checked all limits and safety found okay. The UV light is on and working. The Return air temperature was 70 The supply air temperature was 125. The Variable speed motor inside the air handler is exposed to any high voltage power surges that can lead to more and major damage. Outdoor unit is working okay at this time. Recommendation for unit #1: Add surge protection to the unit. Surge protection required: 1x ECM surge protector for indoor air handler $309.00 1x surge protector for outdoor unit $325.00 Total:$634.00 #2) Top Level/Attic The client did not have any filter for me to replace for the second unit. I do recommend purchasing more and replacing ASAP. I checked all wiring and connections for this unit. I checked all limits and saftys found ok. The UV light is o

No Water Coming From Faucet: Turned water on, checked the two new valves were on and checked for hot water. Nice lady!

Heating Check, Also Check Humidifier: did a fall check out on system. everything checked out fine only recommendations made was that the flu pipe was piped in all cvent and should be upgraded to b vent. also she has 138 days left on UV light bulb and also changed customers humidifier filter.

Valve Leaking: arrived on site for a customer who was a leaking valve customer had hvac out and they notice a valve leaking customer showed me area of concern and it's 2 saddle valves that are leaking let customer know that depending on the city saddle valves are illegal gave customer investment option to replace pipe and replace saddle valves and customer agreed. went to truck to get needed materials and notice i was out of 5/8 x 1/4 angle stop told customer I would run out and get new ones once back shut water off and drained house once drained cut out section of pipe with saddle valves then placed tees and started to dry fit once everything lined up marked and pressed fittings turned water back on and tested for leaks as of ticket completion no leaks were found cleaned up work area and all work related materials thank you for choosing Vito. note: work warranty for 40 days

Performed maintenance on 2016 80% Furnace/AC. Checked all components for proper operation found no issues with components. Checked for loose wires and any dirt. Found blower is dirty and needs to be cleaned. Changed air filter and checked water panel. Confirmed humidifier operations. found humidifier does leak slightly, tried turning down water going in to humidifier and handle started leaking also found separate valve on same line leaking slightly. Informed customer of findings and recommended have a plumber come out to check it. Return call for plumber

RETURN TO INSTALL PARTS. I returned to replace Ignitor and flame sensor. I checked operation and ran through its cycles found everything running and heating ok.

FALL MAINTENANCE ON 2022 90% HIGH EFFICIENCY GAS FURNACE AND ONE 2021 CARRIER HEAT PUMP #1 Lower level has furnace I checked the 16251 filter and replaced with one costumer provided . I checked the indoor blower wheel motor housing compartment for any obstructions and found none. I checked blower amps and found within specs. I checked the inducer draft motor and flue vent pipe and found okay. I checked inducer motor and found within specs. I checked the flame sensor and cleaned it off today. I checked the igniter reading 55ohms. I checked all limits and safety and all wirings and connections found okay. I checked and cleaned burners and heat exchanger. I checked the temperature rise and I got a return air temperature of 72 and a supply air temperature of 123. As of now the unit is running and heating properly with great temperatures and parts are reliable. The UV light is on and working. #2 Top lvl Heat pump I checked and replaced both filters with one costumer provided I check

arrived on site for a plumbing inspection started by flushing heater while flushing inspected all plumbing in the house tested house pressure and is at 65psi which good when inspecting the water heater notice expansion tank is punchred expansion tank should have have water come out of them heater is also from 2013 and is a 80 gallon electric heater also 12 years old and heater have a life span of 8-12 years if maintained properly. when inspecting the rest of the house only found 2 issues in the master bathroom flapper looks worn and in the boys bathroom flapper is warped and toilet is running found no other issues in today inspection brought concerns to the family friend since home owner is not in the states right now and will leave investment options wrapped hose up and shut water off to house toilet so water bill won't go up thank you for choosing Vito. investment options: expansion tank replace:489 flapper replacement:149x2 water heater options (if considering a new heater we

HVAC MAINTENANCE: I serviced 90 percent gas furnace.i changed customer filter 20x20x1. I also cleaned flame sensor and checked ignitor ohms 51. I took temp rise return 73 supply 115. I completed combustion analysis on furnace. I also took amp readings on all motors. I checked all safeties devices and gas valve for proper voltage and pressure . I serviced heat pump. I checked heater kit amps. temp rise. I replaced customer provided filter. I checked defrost controls and fuses in disconnect. 35/5 capacitor reading 34/4.8 compressor amps 4.11 and fan .50. system heating properly at this time

I arrived at my customer home for a one system heat maintenance outdoor temperature is 56 degrees at this time customer like his/her thermostat set between 65 and 80 degrees in the home I adjusted customer thermostat five degrees above the room temperature in heat mode customer provided all air filters I check all amps and components indoor and outdoor Lennox heat pump system working properly at this time system age 2019.

I arrived at my customer home for a one system heat maintenance outdoor temperature is 56 degrees at this point customer like his/her thermostat set between 65 and 80 degrees in the home I adjusted customer thermostat five degrees above the room temperature in heat mode customer provided all air filters I check all amps and components indoor and find the system exceed the ppm limit system age 2007 i recommend a replacement of the full system. system sold by Andrew will install on 11/07/24

FALL MAINTENANCE ON 80% GAS FURNACE I checked the filter and replaced with one costumer provided. I checked the indoor blower wheel motor housing compartment for any obstructions and found none. I checked blower amps and found within specs. I checked the inducer draft motor and flue vent pipe and found okay. I checked inducer motor and found within specs. I checked the flame sensor and cleaned it off today. I checked the igniter reading 55ohms. I checked all limits and safety and all wirings and connections found okay. I checked and cleaned burners and heat exchanger. I checked the temperature rise and I got a return air temperature of 72 and a supply air temperature of 123. I checked humidifier found okay. As of now the unit is running and heating. After today's inspection I can conclude that the unit is working effectively and efficiently as of now. Recommendation Add an Aerus Air Scrubber $1132.00

FALL MAINTENANCE ON 2 80% GAS FURNACE 2016 #1 BOTTOM LVL I checked the filter filter and replaced with one Costumer provided. I checked the indoor blower wheel motor housing compartment for any obstructions and found none. I checked blower amps and found within specs. I checked the inducer draft motor and flue vent pipe and found okay. I checked inducer motor and found within specs. I checked the flame sensor and cleaned it off today. I checked the igniter and noticed white spots on it indicating it is brittle. I checked all limits and safety and all wirings and connections found okay. I checked and cleaned burners and heat exchanger. I checked the temperature rise and I got a return air temperature of 72 and a supply air temperature of 123. I checked humidifier found okay. I checked Rmax UV light and found working okay as of now. As of now the unit is running and heating but 2 parts are no longer reliable. Those two parts have wear and tear on them due to normal operation. These t