Ashburn, VA

arrived onsite, performed plumbing inspection and flushed water heater for approximately 30 minutes. found one issue with powder room toilet - customer notices water seeping through floor close to toilet. possibility of deteriorated wax ring seal. gave customer summary of findings form with quote for new toilet seal. cleaned up work area by water heater after flush.

Mini Split Not Working: need to return next week to complete nitrogen pressure test. on minisplit. could not collect please reach out to customer for diagnostic fee

Performed leak search on mini split system going to master bedroom and outside system. During leak test found leak is coming from head inside of master bedroom. System is under parts warranty labor is not covered. Will order evaporator coil and when it comes in will come back out to install. Labor Currently is $1500 for everything.

I inspected gas furnace in outside closet. inducer motor pulling .48 amps and blower amps 2.89. I cleaned flame sensor. I checked all wire connections and tightened. I checked all safeties as well as gas pressure 3.4 inches w/c. return is 75 supply is 131. stack temp is 309, oxygen is 8 %. co 61 ppm. system is heating properly at this time thank you for choosing vito services.

FALL MAINTENANCE ON ONE UNIT. CLIENT HAS SOLD THE HOUSE. I did a full run down on the whole split system. Filters were cleaned before arriving. Steam humidifier canister also changed before today's arrival. I checked amps on Ecm motor and inducer motor found okay. ECM motor is recommended to have a surge protector on it due to it being exposed to any high voltage power surges. I checked Heat pump wiring and connections all limits and saftys found okay. I checked em heat furnace and found all wiring and saftys okay. The ignitor is okay but the flame sensor does have major wear and tear on it. The client advised me that the house has been sold. The system is running and heating as of now. Recommendations: Add Ecm surge protector $264 Replace flame sensor $379.00 Thank you for choosing VITO SERVICES.

Call to do maintenance on 2023 90% furnace/AC. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. Found system in good condition no issues at this time. Humidifier pad does need to be changed. Customer agreed to change pad today. Changed humidifier pad and collected check with full balance. Final cycled system at this time system is operational.

Performed maintenance on 3 mini split systems and diagnose 4th system. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. 3 system are working properly at this time. Found on 4th that it is low on refrigerant. Will have to come back and perform nitrogen leak test to determine where leak is. Topped system off with 410a and cycled system at this time system is operational. Customer would like a call to go over warranty of system.

Call to do maintenance on 2014 90% Furnace/AC. Checked all components for proper operation found no issues with components. Checked for loose wires and any dirt found blower is slightly dirty and should be cleaned. Checked heat exchanger and found large hot spots. Final cycled system at this time system is operational. Recommended adding Air Scrubber $1100 Humidifier $1100

No Heat Call: found a unit from 2022 low on 410 causing system to go off on low pressure. we need to return to complete a leak check. standing pressures are 110 on low and 200 on high side. system runs for 4 seconds low side pressure drops to 70 and high side increases to 380 and system cuts off. txv needs to be replaced.

HVAC Installation: Installed new furnace, AC and Coil. Thank you for choosing Vito Services

Call to do maintenance on 2 systems. Checked attic system first and found 2016 Furnace/AC. Checked all components for proper operation and found blower is over amping upon start up. Warranty for this system ends 2026 and labor is not covered. Found blower should be cleaned as well. Found no other issues with system at this time. Checked basement system 2006 Furnace and 2016 AC. Found system is operating normally checked all components and found no issues at this time. performed combustion analyzer test and found system in good standing. Did not see any cracks on heat exchanger but there are stress marks. Informed customer of findings and recommended replacing system because of age and condition of system. Customer needs new filter and humidifier pad. Customer wants to change them on his own. at this time system is operational. Blower motor replacement $689 Cleaning blower in attic $369 Duct cleaning $1738

New Backflow Rebuild: installed three test cocks and performed the certification test.

replaced three test cocks and performed the certification test.

Arrived on site. Knocked door and rung door bell several times. I called both numbers on file and went straight to voicemail. The maintenance will need to be rescheduled. I will let the office know.

Performed maintenance on 2 systems. checked attic system 1st it's a 2023 Heat pump found all components working and clean. UV light is still lit. No issues at this time. Checked basement system and found not issues at this time. All components are working properly and are clean. UV light is still lit and working. Final cycled system at this time system is fully operational. Recommend adding humidifier to home. $1100

HVAC Maintenance: I completed two 90% gas furnace inspections, I took Delta T on all systems as well as Clean all flame sensors check both igniters took and draws on all motors and major components I also completed combustion analysis on both systems upstairs gas furnace heat exchanger is severely cracked.I recommend to replace system.

FALL MAINTENANCE ON ONE UNIT. Costumer advised me that she wanted me to only change the filter. wants to reschedule maintenance. Very hard to find parking.

NO HEAT NO AC CALL THERMOSTAT BLANK. I arrived on site and noticed blank thermostat. I went to the furnace downstairs in the basement and noticed water in emergency drain pan and made the bulldog float switch cut the unit off. I shop vac all the water and checked condensate line for clogged lines. I cleared line with 3 gallons of water and ran normaly to Condensate pump. i added Condensate tablets as well. after clearing line and resetting switch the unit still did not come on. I replaced float switch and unit came on I ran it through its cycles and checked full operation and found running and heating as of now. Diagnostic fee $120 Minor repair $220 Bulldog float switch $399

Performed maintenance on 2020 AC/Furnace. found system is in good condition. blower is clean and all components are working properly. fully cycled system found no issues at this time. Informed customer of finding and recommended signing up for VIP membership. customer declined at this time and has a $49 coupon on maintenance today. collected $49 at this time system is fully operational.

Estimate to Rebuild Backflow Preventer: Went to job and spoke with bill by phone. After getting his permission I put a test on the assembly. Assembly is only in need of some fairly simple work but will require some parts. I will get a proposal out as soon as possible.

HVAC Unit Making Loud Noise When Running AC: retape return from install unit is under a year old

Commercial Plumber Call: Arrived at location, contacted the customer. Customer advised us that they had a 1 1/4 main pipe leaking. Manlift was needed in order to reach pipe. Upon observation, the pipe was badly corroded and insulated. Customer drained the building prior to arrival. Cut out 10 feet of the corroded pipe, installed new pipe. Proceeded to turn on water to test for leaks, once water was back we then found that the pipe had more hidden pinholes under insulation. went back out to the supe house to get new pipe and also two coupling in order to make the new connection. once back on site we cut about 30inches of the bad pipe with the pin holes. installed new pipe and then tested for leaks . no leaks detected. clean up work area , pack up equipment and left job site. Thanks for choosing Vito !

NO AC. unit kept short cycling. i checked all connections all wiring and voltages. The pepco box connected to the Contactor was shorting the unit at the disconnect box. I disconnected wirings from transformer and changed 2 pole Contactor for single pole Contactor. I checked operation of unit and now running and cooling properly. Minor repair $185 DISPATCH FEE $120 Costumer was waived the diagnostic fee dispatch confirmed.

09/13/2024 no AC no air blowing I went to the thermostat I called for cooling I heard the outdoor compressor and fan start spinning and running. I went to the air handler downstairs in the basement I heard refrigerant running through the lines but I did not hear the indoor fan motor running. I checked for voltage at the board for the blower motor 24 volts present. I called for heat and for cool and neither times of the blower motor come on. the blower module has been compromised we will have to order part and replace. I will send part information to Richard so he can call manufacture on Monday and check for availability. Price to replace blower motor and squirl cage will be $2250.00 The office will contact client once we get availability and get their approval to order and to return to install. Thank you for choosing VITO SERVICES. DISPATCH FEE is waived today.

09/12/2024 performed maintenance 12 year old carrier Infiniti system supply 48 return 70 filter are in good condition,drain flushed inspect evap coil and blower motor.noticed air purification(rmax) need a new UV bulb condenser coils are in need of a cleaning,all electrical tested within specs refrigerant levels are good at this time thank you for your business replacement of UV bulb 411 condenser coil cleaning 424