Centreville, VA

I replaced 16x25x1 filter. I cleaned flame sensor and checked ignitor ohms 46. I took amps on inducer and blower motor . i checked all rollout and high limit safeties. I checked 240 and 24 volt connections and tightened. I reset uv light went off on error code 3. customer will purchase new bulb and I will return and replace. I replaced humidifier pad and tested operations and set control to setting 4 32%. dampers are in open positions. return is 70 supply is 129. lastly I completed co combustion analysis on system. daikin gas furnace is heating properly at this time . thank you for choosing vito services. returned and replaced uv bulb and test operation.

FALL MAINTENANCE ON ONE UNIT 2018 CARRIER 90% GAS FURNACE I checked the filter and found really dirty, the client advised me that he had replaced it about 1-2 months ago. I checked the indoor blower wheel motor housing compartment for any obstructions and noticed a fungle outbreak cultivaing within the unit. The blower motor is a variable speed motor and a very expensive one. I noticed that the blower motor is exposed to any high voltage power surges due to not containing a surge protector. I checked the Inducer draft motor and flue vent pipe and found okay. I checked inducer amps and found within specs. I checked the flame sensor and cleaned off today. I checked Ignitor amps and ohms and found reading within recommendations. I checked and cleaned the burners and heat exchanger. I checked all wirings and connections and all limits and safetys . I got a return air temperature of 70 and a supply air temperature of 135 I checked both stages on this gas furnace and both kicked on low and

New Furnace Installation: recovered all old refrigerant and removed all old equipment and set and installed all new equipment and tied everything back in from drains to wiring and duct work and fired everything up in ac and heat mode to check for proper operation

System is a 2023 80% furnace AC. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. Found blower clean along with evaporator coil. System does not have a UV light or humidifier. Changed Air filter. Final cycled system at this time system is operational. recommendations are humidifier 1300 air scrubber 1100

NO HEAT , UNIT MAKING LOUD NOISE I arrived on site at this unit that is 10years old. The client advised me of the loud noise the unit was making. I cut the unit on and. addressed the noise outside. The compressor was making a clacking noise. I took compressor amps and was reading 14 amps and cutting off once reaching 14 amps. I checked my pressures and I got a PSI of 50 on the low side and I got a PSI of 500 on the high side. I came to the indoor unit and noticed the blower motor not running. There is two sets of wire and one of the sets is going to the outdoor unit. I checked the breaker at the air handler and found no voltage at the breaker. I by passed breaker and the fan tried to come on but instead it was noisy humming, and 24v was present at the fan at the board. So instead of fan running the aux heat came on. if the aux heat runs continuously it can damage more things. The unit has reached its life expectancy. Option #1 Repair Replace blower $2200.00 replace breaker $6

I replaced 16x25x1 filter. I cleaned flame sensor and checked ignitor ohms 46. I took amps on inducer and blower motor . i checked all rollout and high limit safeties. I checked 240 and 24 volt connections and tightened. I reset uv light went off on error code 3. customer will purchase new bulb and I will return and replace. I replaced humidifier pad and tested operations and set control to setting 4 32%. dampers are in open positions. return is 70 supply is 129. lastly I completed co combustion analysis on system. daikin gas furnace is heating properly at this time . thank you for choosing vito services.

Performed maintenance on 2010 Furnace/AC. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. Found blower is dirty and need to be cleaned ($393). Filter needs to be changed. Performed combustion analyzer test found system is with in code for C02 emissions. System is out of warranty recommended adding surge protector for system ($309). Also hot water tank is not up to code customer is missing expansion tank ($508). Final cycled system at this time system is operational. Customer gets 10% off for being a member.

HEAT MAINTENANCE ON ONE UNIT 80% Carrier Gas furnace 2023 I checked the 16254 filter and replaced with one costumer provided. I checked the ECM blower motor and noticed it is exposed to any high voltage power surges. I checked the blower wheel for any obstructions and found none. Blower amps found within specs. I checked inducer draft motor and flue vent pipe found okay I checked inducer amps and found okay. I checked and cleaned burners and heat exchanger. I checked flame sensor and ignitior found okay. I checked all limits and saftys and all wiring and connections found okay. I got a return air temperature of 74 and a supply air temperature of 124. No humidifier in site. The unit is one year old and running nice and efficient. After today's inspection: I recommend to add a surge protector to the blower motor due to not being exposed to any high voltage power surges that can lead to damaging other components. Surge protector $309.00 I will also recommend the client sign up for ann

I replaced customer filter and cleaned drain line. I checked transformer and relay a well as took amps on blower motor and heater kit 20.32. I took temp rise return 76 supply 121. I tested system in defrost controls and checked contactor and 40/5 capacitor. reading 40 and 4.9. I also took Amps on compressor 6.21 and fan .56. I checked 410 charge within range. outdoor coil is dirty I recommend chemical coil cleaning and installation of surge protectors. system is 13 years old but still heating properly at this time. Thank you for choosing vito services.

Performed maintenance on 2013 Heat pump system. Checked all components for proper operation. Found everything is working properly. Blower is mostly clean. All emergency heating elements are working. Found evaporator coil is rusted from normal wear and tear. RMax bulb is still good and bright. Changed out humidifier pad per garneski maintenance agreement. Checked condenser unit and found system is working. Starting components are in good standing. Compressor is amping at 50% above average. Condenser coil needs to be cleaned. Final cycled system at this time system is operational. Recommendations Condenser Cleaning $247 Yearly membership $244

Call to do maintenance on 2022 Furnace/AC. During maintenance found all components are amping properly. Temp rise was 60 found blower is dirty and needs to be clean. Flame sensor and ignitor are in working order. Customer does not have air scrubber or humidifier. At this time system is fully operational. Recommendations 1. Blower clean $369 2. Humidifier $1200 e. Air scrubber $1100

NO HEAT CALL. TECH WAS OUT HERE ABOUT A WEEK AGO TO DO A FALL CHECK UP I DID A FULL DIAGNOSIS SYSTEM AND FOUND LOOSE WIRE IN THE FURNACE I CONNECTED LOOSE WIRE BACK UP TO THE FURNACE CALLED FOR HEATING AT A THERMOSTAT RAN INTO IT CYCLES FOR ABOUT 45 MINUTES FOUND EVERYTHING CLEAR AND GOOD TO GO. no charge today.

arrived at location for a plumbing inspection, customer states water pressure was too high and I looked on the main line and saw an old prv and recommend to replace since I was here already customer agreed to replace and before doing any work pressure was 100 psi and now its at60 psi no leaks occured

FALL HVAC MAINTENANCE CHECK checked filter 16x25x1 doesn't need changing, checked indoor blower motor and wheel, cleaned and checked burners and heat exchanger, checked inducer draft motor and flue, cleaned and checked flame sensor , checked all safeties and limits, checked temperature rise 30-60 return air temperature 74 , supply air temperature 123 ,. PAYNE MODEL NUMBER 58STA090-16 SERIAL NUMBER 4503A40298

I performed a one-system heat maintenance on a 2011 80% gas furnace with AC/coil. The thermostat was adjusted five degrees above room temperature in heat mode. I flushed the indoor drain pipe and checked all components. Supply temperature read 140.2°F, return temperature 88.9°F, and amps were within normal range. The blower fan motor showed oil leakage, burners had rust on edges, and the ductwork and system need cleaning. Flames were blue, and the system was functioning properly.

I arrived at my customer home for a one system heat maintenance outdoor temperature is 74 degrees and raining at the time customer like his/her thermostat set between 65 and 80 degrees in the home I adjusted customer thermostat five degrees above the room temperature in heat mode customer provided all air filters I flush the indoor drain pipe and pump check all amps and components indoor 90% gas furnace with humidifier and sanuvox working properly at this time. Air Scrubber system comes with a 5-year manufacturers system warranty, 2-year bulb manufacturers warranty and 90 day labor warranty through Vito.

09/16/2024 performed maintenance on 2 goodman system attic and basement unit is good physical and operational conditions all safeties and controls tested within spec,no loose or damaged wiring thank you for your business

09/16/2024 performed maintenance on 2 goodman system attic and basement unit is good physical and operational conditions all safeties and controls tested within spec,no loose or damaged wiring thank you for your business

08/29/2024 performed maintenance 10 year old carrier unit supply 52 return 74 flushed drain ,changed filter inspect blower motor and evap coil after homeowners approval cleaned evap coil and sign homeowners up for home service plan refrigerant levels with spec all system is now in good physical and operational conditions thank you for your business

08/26/2024 NO AC CLIENT WANTED ME TO LOOK AT BOTH UNITS. BOTH HAVING ISSUES. #1 basement and 1st floor. The thermostat was blank. I checked all safety and found EZ trap safety switch off due to back up. I recommend client to flush it with nitrogen but he declined all he wanted me to do was use the brush and pour a gallon of water down it. I also added Condensate tablets. After flushing line with gallon of water and cleaning it the unit came on and started running. I got a return air temperature of 70 and a supply air temperature of 49. The unit was left running and cooling. Condensate tablets $35.00 #2 Second floor. costumer had advised me that she is concerned as to why does a Unit that just get installed does not reach down to 69 even on cool days. I checked operation of system everything came on and ran. I got a return air temperature of 71 and a supply air temperature of 54. I checked pressures and found a little low. I added just one pound of R-410A After adding the on

I arrived on site to perform a plumbing inspection and HVAC inspection for a customer. I let him know to flush the heater and sign up for our service plan. The tenant said he would call me later to sign up, but I couldn't get a hold of him. Once he gets a response, he will call us back. Thank you for choosing Vito.