Upper Marlboro, MD

Today, I arrived on site to assess the furnace situation. Detected a small smell of gas during the first startup. No lingering smell was present after initial operation. The system is currently operating properly without any issues. Recommended monitoring the system for any changes in gas smell during future startups. Overall, the furnace is functioning as expected at this time.

arrived on site for a clog sink and a leaking sink customer showed me 2 areas of concern in the hallway way bathroom sink was clogged then in master bathroom was a drippy faucet then under sink they had buckets notice pop up arm was broken causing it to leak when sink was ran customer told me customer is a tenet called up landlord and explained my findings and gave options today when with snaking sink, replacing Moen cartridge, and replacing pop up assembly also landlord singed up for our service plan. started in hallway bathroom used pistol snake and snaked from the top after 5 ft standing water went down then pulled cable back and had hair on the head ran water for a few minutes and no back ups occurred then in master bathroom shut water off to house and drained once drained removed faucet Handel and removed clip then pulled old Moen pull cartidge then cleaned up pipe and greased new cartridge and set in place and placed clip back once down took apart p trap and removed old pop up as

Today, I arrived on site to assess the heating system and address some issues. Heating System Assessment: Found the system going off on error code 22. Identified the high limit switch as faulty. Performed a combustion test; system measured 8ppm and was heating properly. Replaced the high limit switch, and the system is now running properly. Safety and Code Violations: Discovered major discrepancies with the gas flex line into the furnace housing; installation is against code. Noted that the system was installed in 2022 without following proper regulations. Recommended necessary gas repairs to ensure safety and compliance. Air Conditioning Issues: Observed that the copper coupling is halfway cut through; video evidence is available. Advised that this piece should be removed. Noted that the line set needs to be covered, and the TXV should be properly wrapped. Found flue connections at the furnace to be improper; flue from coupling back to the furnace is installed backwards.

arrived at the job side when I try to move the scissors lift and it was not working how so ever I try everything and it was a new model that I never used before. so it has to be rescheduled for the next day because the didn't inform the people next door bout turning off the water for the whole building. Returned to the jobsite and learned how to used the scissors life. once I got it to where the leak was it I saw that it was a 2" mail line. cut the water off and started to drain the whole system. it took a while because the like goes all the way across the building. once it was drain I cut where the leak was and fix the leak. also added a 3/4 vlad for the future hose bibs replacement because the valve they had was leaking and not holding. once I was done I fill up the whole system to make sure both repairs were good and no leaks. collected all my tools and clean my work area. THANK YOU FOR CHOOSING VITO

Today, I arrived on site for heating maintenance on the furnace. Inspected the inducer motor, pressure switches, tubes, ignitor, and flame sensor; all components are functioning well. Blower capacitor measured at 7.4, which is within the acceptable range of 7.5. Noted significant rust on ducts surrounding the HVAC equipment. Verified that furnace voltage and amps are within specifications. Confirmed that the temperature rise is good, indicating the system is heating properly at this time.

Main Water Valve Is Leaking: arrived onsite, tightened packing nut on existing main water gate valve. advised customer that eventually it will need replacement, but he will be okay for now. collected dispatch fee only

09/12/2024 arrived on site to repipe radiators lines started by tape and doping male adapters and tighten on 1 1/4 female shark bite adapter once tighten cut out old pex adapter out and set in place. then threaded on male adapter to the 90 and tighten once tighten started to dry fit tee and other fittings remove old brown pipe from 1/2 90 and placed a 1/2 male press adapter once all fittings lined up marked for proper depth when pressing the tee jaws seems to crushed fittings and didn't press went to supply house to get a new fitting once back notice they gave us the wrong size sitting went back and back a sweat tee cleaned up pipe and sweated in placed once sweated pressed all fittings and turned water back on and tested for leaks and aired out radiator as of ticket completion no leaks were found cleaned up work area and all work related materials thank you for choosing Vito.

09/12/2024 arrived on site to repipe radiators lines started by tape and doping male adapters and tighten on 1 1/4 female shark bite adapter once tighten cut out old pex adapter out and set in place. then threaded on male adapter to the 90 and tighten once tighten started to dry fit tee and other fittings remove old brown pipe from 1/2 90 and placed a 1/2 male press adapter once all fittings lined up marked for proper depth when pressing the tee jaws seems to crushed fittings and didn't press went to supply house to get a new fitting once back notice they gave us the wrong size sitting went back and back a sweat tee cleaned up pipe and sweated in placed once sweated pressed all fittings and turned water back on and tested for leaks and aired out radiator as of ticket completion no leaks were found cleaned up work area and all work related materials thank you for choosing Vito.

09/05/2024 arrived on site for a leaking radiator pipe customer showed me area of concern and said he had another company out here and they were replacing the radiator pipe then a tee snapped for the radiators going up customer had months going back and forth with that company till they sent his money back. look and saw it's something we can do gave customer investment options and customer went with the repipe line is 1 1/4 and parts will have to be ordered customer would like this job to be scheduled for next week Thursday thank you for choosing Vito.

07/26/2024 Customer called and cancelled in the morning

06/21/2024 Did AC maintenance, system just turned 2 years this month. Checked Air filter and temperature differential, ok for now. Checked and tested drain line and no issues. Checked Blower motor amps and overall indoor unit working ok. Checked Outdoor unit, capacitor, contactor ok. Compressor and fan motor amps ok as well.

AC Maintenance 06/20/2024 Today, I arrived on site to perform cooling maintenance for the customer. Here is a summary of my findings: Inspection: Filter: The filter is in good condition and does not require replacement at this time. System Performance: Temperature Split: The temperature split is 22, indicating that the system is cooling properly. Condensate Pump: The condensate pump is operating normally. Outdoor Unit: Capacitor: I found that the capacitor is rusty, but it is still within specifications. System Pressures: The system pressures are within specifications. Voltage and Amps: The voltage and amps of the system are also within specifications. Overall, the system is cooling properly and no repairs or replacements are needed at this time.