Chantilly, VA

arrived on site to replace a water in the ceiling of the janitorial closet, took out the ceiling tiles and had some trouble fitting the lift in the closet, eventually managed to get the old heater out and eventually got the new one in, hooked up the hot and cold and electrical, no leaks, water heater started heating slowly, cleaned up work area and left

Commercial Plumber, 2nd Floor Kitchen Sink Backed Up: arrived on site for a customer who has a leaking faucet customer showed me area of concern and said they notice on the fuacet water starts to leak out from the connection from the faucet and spray down hose and he turned off hot side fuacet and angle stop started leaking told customer he can call Kohler to get a new fuacet from warranty since normally that part never leaks but today customer signed up again for vip plans and a new a angle stop started by shutting water off to house and let house drained once drained removed supply lines and unthreaded old angle stop and removed and placed new angel stop in place and tighten and turned water on and tested for leaks and as of ticket completion no leaks were found cleaned up work area and all work related materials thank you for choosing Vito. note:40 day warranty on angel stop

FALL MAINTENANCE ON 2022 80% GAS FURNACE I checked the filter and found okay for now. I checked the ecm indoor blower wheel motor housing compartment for any obstructions and found none I did notice that the blower motor is exposed to any high voltage power surges by not containing a surge protector on it. I checked blower amps and found within specs. I checked the inducer draft motor and flue vent pipe and found okay. I checked inducer motor and found within specs. I checked the flame sensor and cleaned it off today. I checked the igniter reading 55ohms. I checked all limits and safety and all wirings and connections found okay. I checked and cleaned burners and heat exchanger. I checked the temperature rise and I got a return air temperature of 72 and a supply air temperature of 123. I checked humidifier found okay. I detected a fungle growth cultivating within the unit near the humidifier and near the coils and the the wirings of the blower motor. As of now the unit is running and

FALL CHECK ON ONE HEAT PUMP 2023 I checked the filter and replaced with one costumer provided I checked indoor blower wheel motor housing compartment for any obstructions and found none. This unit has an ECM motor but no surge protector. I checked all wirings and connections found okay I checked all limits and saftys found ok. AUX heat working fine. I got a return air temperature of 72 and a supply air temperature of 112. I checked outdoor condenser coil and found okay this unit carries a inverter. I checked all amps found within specs outdoor temperature 54 discharge temp 44. This unit is running and heating efficiently as needed. After today's visit I will advise the client of the recommendation to add a surge protector to the unit. $309.00 The client has decided to not do any additional work as of now. Thank you for choosing VITO SERVICES.

Men's Locker Room Single Stall Backed Up: Arrived at location. Inspected the toilet. Saw the toilet was clogged. Proceeded to remove the water and turn the toilet off. Removed Toilet and Used the 1500 to snake the line. Snakes the line and unclogged the toilet. Cleaned the Area and put new wax ring and put the toilet back. Added fresh Calking and cleaned up.

FALL CHECK UP ON HEAT PUMP I checked the filter and found okay for now. I checked the ecm indoor blower wheel motor housing compartment for any obstructions and found none I checked blower amps and found within specs. I checked all limits and safety and all wirings and connections found okay. i checked electrical heater element and found okay. Aux heat working fine. I checked the temperature rise and I got a return air temperature of 72 and a supply air temperature of 123. i checked EVAP coil and found dirty. I detected a fungle growth cultivating within the unit and near the coils and the the wirings of the blower motor. I checked outdoor coil found okay. 45/5mfd capacitor found within specs. Single pole Contactor found okay. Defrost board found okay. As of now the unit is running and heating. Recommendations: #1 Clean EVAP coil $475.00 #2 Add air scrubber $1000.00 The client has agreed to the recommendations and I did perform job. I collected $1475.00 Client paid with credit ca

Performed maintenance on 2021 furnace. found all components are working properly. not finding any issues at this time. changed filter with new one. Getting 60 degree temp rise. found Rmax bulb is blown out. recommended replacing bulb. customer at this time customer wants to weigh options. at this time system is fully operational. Recommendation: replace Rmax UV light $708 Ez Trap switch $499 Blower surge protector $198

Performed maintenance on 2016 Furnace. found all components are working. Found both flame sensor and ignitor are starting to fail and should be replaced before they do. informed customer of finding and customer want to wait to do repair. at this time system is operational. Ignitor $400 Flame sensor $364

FALL HVAC MAINTENANCE CHECK checked filter 20x20x1 don't need changing, checked indoor blower motor and wheel, found no ECM MOTOR protector, checked emergency heat strips all electrical wire connections safeties and limits, checked emergency heat return air temperature 77 , supply air temperature 120 , 15 kw , checked heat pump side return air temperature 103 , checked the inverter board and contactor, checked all electrical wires safeties and connections, found no surge protector, checked defrost cycle, checked outdoor air temperature 64 , checked discharge air temperature 59, checked freon level liquid line temperature 101 , suction line temperature 123 ,. CARRIER MODEL NUMBER 25VNA036A300 SERIAL NUMBER 2917E06527

Pipe Leaking In Ceiling: arrived on site to look at a leak in the ceiling, leak is coming from a water heater in the ceiling of a janitorial closet, bottom of the heater is completely rusted out and pan is full of water and cracked causing leaks, talked to customer and recommended getting the whole heater replaced, customer agreed, customer requested the heater be shutoff to prevent more leaks in the mean time, shut off electrical and water supply to heater, customer wants a quote to replace heater, cleaned up work area and left

Commercial Water Heater Flush: arrived on site to do preventative maintenance on a water heater for the old deli on the 1st floor, made sure water and electrical were off, drained the heater, had to fight with sediment for a few attempts before it would drain, got heater to drain with a pump, checked the elements while it was draining, elements are getting old but still in good condition, once drained the heater went to fill it back up and was not getting any water, valve to control water supply has gone bad and needs replacement, cleaned up work area and left

Local Commercial Plumber, Water Leaking from PRV: arrived on site to look at a water heater that was leaking, customer said that he believes it to be leaking from the threads of the PRV, confirmed that the leak is from the PRV, customer wants to get a price for replacing the whole heater as it is old, cleaned up work area and left

performed hvac maintenance on 2 year old carrier heat pump system is good physical and operational conditions refrigerant levels are good at this time all electrical tested within spec thank you for your business

09/11/2024 arrived on site to look at a mop sink faucet that won't fully turn off, seems to be a stem issue on the hot side, no nearby shutoff valves anywhere near faucet so building shutdown and drain is in order, customer wants entire faucet replaced, will need to return early tomorrow morning to replace it, no repairs done until then, cleaned up work area and left 09/12/2024 arrived back on site early in the morning to start on replacing the faucet, shut down the building and started draining the line, took apart the old faucet and replaced it with a new one, once tightened restored water and tested for leaks, no leaks or issues found, cleaned up work area and left

08/29/2024 arrived on site to look at a 1-1/2 CI drain line that was cracked and leaking in the ceiling of a 2nd floor room, put plastic down on the floor and took apart the old pipe, replaced it with new, bigger 2 inch pipe for better drainage, tightened all fittings and tested new pipe, no leaks, cleaned up work area and left

08/27/2024 AC MAINTENANCE ON TWO UNITS. #1 Attic space. I checked filter and found clogged costumer will need to purchase more and replace. I checked the indoor blower wheel motor housing compartment for any obstructions and found none. i checked blower amps and found within specs. i checked evaporator coil and I checked Condensate line and flushed it with a gallon of water and found okay. I checked all other limits and safety and all wiring and connections found okay. I got a return air temperature of 80 and a supply air temperature of 59. I checked outdoor unit coil and found in good shape I checked all outdoor components and found within specs. outdoor temperature 92 discharge temperature 102 This unit is running and cooling as of now. #2 basement I checked and replaced filter with one costumer provided I checked indoor blower wheel motor housing compartment for any obstructions and found okay. I checked blower amps and found within specs. I checked the evaporator coil and

08/26/2024 AC RUNNING NONSTOP I arrived today to address costumers concerns , I called for cooling at thermostat and only the indoor fan came on. I checked my temperatures and got no reading. I went to outdoor unit and heard only the fan spinning. I cut the power and found some burnt wires at the capacitor. I repaired wires and replaced capacitor and compressor and fan both came on. The unit start running and cooling. While inspecting unit I noticed an excessive amount of fungal growth cultivating within the unit. I showed costumer and recommended air scrubber. She agreed to recommendations today. I checked operation of full system I got a return air temperature of 80 and a supply air temperature of 61. If there is any questions of concerns please feel free to call us. Thank you for choosing VITO SERVICES. Capacitor $340.00 Air Scrubber $1132.00 (comes with a 5yr manufacturers system warranty, 2yr bulb manufacturers warranty and 90 day labor warranty through Vito)

Aug 22, 2024 Arrive at location. Backflow was leaking from the ball valve, Proceeded to tighten the ball valve. Managed to stop the leak temporarily, the customer was advised that it was stop temporarily and was fine with it. It is a 2 inch blowflow and the customer would like 2 different estimates. First estimate would be to replace 2 inch ball valve from the inlet of the backflow. Second estimate would be replace inlet and outlet ball valves including the backflow.

08/14/2024 arrived on site to look at 2 sinks that had traps that were leaking, no popup drains were installed on the sinks, both old traps were cracked and leaking, ran out to pick up some new 1-1/4 chrome p traps and install them on the sinks, took apart the old traps and installed the new ones, tested both lines for any further leaks, no leaks found on either sink, cleaned up work area and left

08/14/2024 Arrived on site. Cut out leaking section. Removed section. Threaded new male adapter and solvent welded pipes and fittings. Secured new section and cleaned up work area. Removed all work related tools, debris, and equipment from site.

07/19/2024 Waited for miss utility and machine arrived. Water line marked. Cut asphalt and dug down to pipe. Cleaned pipe surface around break. installed repair clamp. Returned water service to building. Found no leaks. Restored full pressure slowly. Cleaned up work area.

Commercial Plumbing Call Pro Press Valve Needs to be Replaced 06/18/2024 Arrived on site. Shut off water to the building and began draining. Installed temporary discharge pipe. Sweat off old leaking valve. Cleaned pipe surfaces and installed new valve. Turned on water to building. Piped in remaining connections and tested for leaks. Found no leaks. Cleaned up work area and removed all work related tools, debris, and equipment from site.