McLean, VA

Replaced wax ring on toilet

FALL CHECK GAS FURNACE BOTTOM FLOOR #1 check filter 16x25x1, needs replacing soon, cleaned and checked burners and heat exchanger, checked indoor blower motor and wheel found no ecm motor surge protector, checked ignitor and flame sensor, checked Inducer draft motor and flue, checked all safeties and limits, checked humidifier and water panel, found no UV light system , checked temperature rise 35°, - 65° return air temperature 70° , supply air temperature 127° FALL CHECK TOP FLOOR HEAT PUMP SYSTEM #2 checked filter 16x25x1 found clogged needs replacing asap, checked indoor blower motor and wheel found no ecm motor surge protector, checked all electrical wires safeties and limits, checked emergency heat strips and operation return air temperature 70° , supply air temperature 110°, checked heat pump side, supply air temperature 71° , supply air temperature 92° , checked outdoor heat pump condenser coil and motor, checked capacitor, checked defrost board cycle, control and operatio

Arrived on site for a plumbing maintenance started by flushing heater while flushing inspected all plumbing in the house notice water heater is from 2017 making it 8 years old and also notice expansion is punchered notice theres not chimney liner as well customer has 2 furnaces and 1 heater if water heater is to by code we need a liner installed no other issues where found in the house gave customer investment option thank you for choosing Vito.

Performed HVAC Maintenance on four systems sent all pictures and checklist to the customer.

FALL MAINTENANCE CHECK ON ONE SYSTEM. From 2019 I checked the filter and found it is still okay , it was changed out in August. I checked the entire operation of the heat pump. Indoor amps are within specs. Blower wheel and evaporator coil are mostly clean. However I did notice the cultivation of fungus that started to spread inside the air handler Insulation. I brought this to the attention of the client and suggested we add 1x aerus air scrubber to the supply portion of the duct work. I continued the inspection and found all wiring and connections okay. All limits and safety’s found functioning properly. Aux heat works, pulling 20amps. I checked drain line just to make sure there are no back ups or overflows. One thing I did want to note is that the entire indoor air handler is exposed to any high voltage power surges due to it not containing a surge protector. Final temperature rise was 50 degrees. I proceeded to check the outdoor unit and hosed down coil with water using clients h

Thank you for your interest in our services. Based on our survey and our discussions James Vito, Inc. will provide the necessary labor, material to complete the work as specified below. SCOPE OF WORK: Supply and install Two new Zurn 1321-XLC wall hydrants. • Shut off water at the wall hydrants’ isolation valve. • Cut out and remove old wall hydrants. • Supply and install two new Zurn 1321-XLC wall hydrants. • Secure hydrants in wall with proper slope for draining and freeze protection. • Test for leaks and proper operation. • Clean up work area and haul away all work related debris. NOTES: • Clear access to work area must be provided the day of the scheduled work. • All work to be performed during normal working hours (M-F) 7AM to 5PM excluding holidays • Any changes to the scope of work may result in additional fees. • All work to comply with federal, state and local codes. EXLUSIONS • No warranty on any existing piping or equipment. MATERIALS: • 2 Zurn 1321-XLC wal

Arrived with my customer home for one system, giving error code their full system check and found one bad blower fan Motor and module. I recommend a replacement of the motor and module parts is unavailable at this time. I provided a proposal a few months ago for replacement. Customer will review both proposal system turned off at this time.

Preformed new system mark-up to be installed

Walked new job...Will have proposal sent out by tomorrow 24th

Arrived onsite, performed plumbing maintenance check. Customer had only one plumbing fixture, the kitchen faucet and connections under sink. I only saw one issue, there was a dual angle stop supply valve with one outlet not in use. It was not capped off and could have potentially caused a flood or leak in the future. Customer gave me okay to make repair. Installed cap and tightened onto valve. Checked for leaks. Cleaned up and removed all job related debris.

Filters: Cleaned reusable filters, no replacement needed. Indoor coil: Inspected evaporator coil, clean and in good condition. Blower wheel: Inspected and cleaned blower and fan wheel, no signs of imbalance. Drain pan/line: Inspected drain pan and flushed condensate line. No clogs found. Electronics: Inspected control board and connections. All appear secure. Condenser coil: Inspected condenser coil for dirt and debris. very clean. Unit clearance: Confirmed the area around the unit is free of obstructions. Refrigerant levels: Checked refrigerant pressure to ensure proper levels. No leaks were detected at this time. Electrical connections: Inspected electrical connections in the outdoor unit. All connections are secure. Fan blades: Inspected fan blades for damage or debris. No issues found. System operation: The system was run through both coolin cycle. Temperature split: The temperature differential was measured and is within acceptable parameters. Noise levels: Norma

No hot water cut into the shower

Service Type: Level 1 Chemical Condenser Coil Cleaning Date of Service: 08/22/2025 Unit Information: Manufacturer: Goodman Model Year: 2021 Unit Type: Residential Condenser System Type: Split A/C System (Outdoor Unit) Scope of Work: Performed a scheduled maintenance cleaning of the condenser coil on a 2021 Goodman air conditioning unit. The service was carried out to improve airflow efficiency, reduce system strain, and optimize cooling performance ahead of peak ge. Detailed Procedure: 1. Initial Inspection: Verified that the system was powered off and safely isolated at the disconnect box. Conducted a visual inspection of the condenser unit for signs of damage, debris, or wear. Checked fan motor, electrical connections, and cabinet condition – no immediate issues noted. 2. Debris Removal: Removed large debris (leaves, grass, dirt) from the condenser cabinet and surrounding area. Carefully cleared the coil fins of surface debris using a soft-bristle brush. 3. Applicat

Arrived onsite, multiple wet areas in customer's basement ceiling. Traced source of leak to 1st floor kitchen area. Cut out basement ceiling drywall in the areas where it was most water logged. Revealed CPVC water lines and PVC drain lines but all pipes were okay. Moved kitchen refrigerator away from wall in kitchen. Opened drywall around refrigerator water supply valve. Ultimately, determined source of leak to be refrigerator itself. Customer has appliance technicians coming tomorrow. Cleaned up and removed all job related debris upon completion. Customer had $90 off any plumbing repair coupon which I honored.

AC MAINTENANCE ON ONE UNIT. I checked the filter and replaced it with one that the client provided. I checked the indoor variable speed motor and housing and found free from any obstructions. I checked motor amps and found within spec, however I noticed that the variable speed motor is exposed to any high voltage power surges due to it not containing an ecm surge protector. I checked the evaporator coil and I flushed the drain line with approximately 1 gallon of water and added condensate tablets to ensure proper drainage to floor drain. While inspecting evaporator coil I noticed the cultivation of fungus growing near insulation. This is normal with time due to the moisture and humidity that the system pulls it gives life to spores because there is nothing fighting against it for example , a UV light. I checked all other limits and safety’s and all wiring and connections were okay. I took temperaturess and got a 20 degree delta T. I proceeded to check the outdoor coil and found clean

- Conducted a comprehensive assessment of the residence and surrounding property to identify a suitable testable backflow preventer. - Determined that no testable backflow preventer was present at the property. - Noted that the homeowners will reach out for assistance if they decide to install a backflow preventer in the future.

Chemical cleaned evaporator coil and condenser coil, added two new surge protectors and performed two-zone duct cleaning

Commercial Plumber Call Clogged Kitchen Sink: Snaked drain line from kitchen sink which was clogged, ran water for about 10 minutes line is now clear

Job Description: install 2 ton ac unit

Looked at system and found system is working correctly found condenser coil is dirty and needs to be cleaned. Final cycled system at this time system is operational.

Estimate to replace HVAC system with new AC Furnace Dual Unit

SCOPE OF WORK: Open walls, oors 1 thru 6, to Cut out existing 4 inch PVC sanitary riser and replace with new pipe. • Engineering will place all affected xtures out of service. • Put down drop cloth for protection. • On the rst night James Vito Inc will open the walls to access the pipe for repairs on oors 1 thru 6. • Clean up and haul away all sheet rock, then cover all access points with plastic sheeting. • On the next night we will begin on the 6th and 5th oor. • Cut out riser and detach from the plumbing xture laterals, then remove the pipe and haul away. • Install new PVC riser, secure at oor penetration with riser clamp. Install cleanout tee and reconnect to plumbing xtures so the xtures will be in service for the next day. • Test for leaks. • Clean up work area and haul away all job related debris. • Repeat process on the 4th and 3rd oors, connecting all xtures to new riser for use the next day. • Clean up. • Repeat process on 2nd and 1st oors. • Test for leaks and cleanup work a

2022 coil cleaning for 1 system and vip membership for 2 systems System Type: Split System (AC + Gas Furnace) Furnace Brand/Model: Carrier, 2022 Cooling Component: Carrier Condenser and Evaporator Coil Inspection & Maintenance Tasks Completed 1. Thermostat Operation ☑ Verified proper function and response ☑ Checked for accurate temperature calibration 2. Air Filter ☑ Inspected and replaced (if needed) ☑ Confirmed correct filter size and airflow direction 3. Blower Motor & Compartment ☑ Cleaned motor and blower wheel ☑ Checked for abnormal noise or vibration ☑ Lubricated if applicable (most motors are sealed) 4. Electrical Components ☑ Inspected contactors, capacitors, relays ☑ Tightened electrical connections ☑ Measured voltage and current draw 5. Evaporator Coil (Indoor Coil) ☑ Inspected coil for cleanliness and mold/debris ☑ Verified proper drainage from condensate pan and line ☑ Cleaned coil as needed 6. Condenser Unit (Outdoor) ☑ Cleaned coil and fins ☑ Che

For this job I did an AC MAINTENANCE ON 2 carrier infinity units. 1s unit 2016 carrier infinity 2016 Indoor 80% funrnace I got a 18 split temp. Client has already replaced 16x25x1 Air-filter. Evaporator coils are clean with no corrosion or leakage. I noticed air ducts were polluted with dust. I made it one of my recommendationa and client is aware. Condensate line is draining with no problem. Control board is functioning and communicating with ECM blower wheel. Blower wheel amps reading 4.5. Outdoor unit 2016 infinity carrier. I noticed coils are clogged with dirt and outside debri and is in need of a coil lvl cleaning. I made this my recommendation and client is full aware. Inverter board is functioning and communicating with system. i noticed system doesn't have a surge protector and I recommended one to protect the systems inverter board for any power surges. Contactor has 240 v. Fan and compressor amps are reading within range. 2015 Indoor 80% funrnace I got a 18 sp

Customer has 2 systems. Started with attic system first. System is a 2022 90% Furnace/ 2016 AC system. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. Found blower is clean along with evaporator coil. System does have an UV light. Checked all starting components on the condenser and found all starting components working. Checked cleanliness of coil found coils do need to be cleaned. Refrigerant level are good. Final cycled system at the time system is operational. System is a 2017 90% Furnace/ 2016 AC system. Checked all components for proper operation found no issues with components. Secured any loose wires and checked for dirt and debris. Found blower is clean along with evaporator coil. System does have an UV light and Humidifier. Checked all starting components on the condenser and found all starting components working. Checked cleanliness of coil found coils do need to be cleaned as well Refrige